Academy›Special courses: eight courses for day-to-day selling›Gear and lighting for product photos: the setup under €150
Special courses: eight courses for day-to-day sellingDIY product photos

Gear and lighting for product photos: the setup under €150

Course lesson 1/3 ⏱ ~15 Min. 🏅 up to 215 points By Enes Kurt Updated November 2026 Check your listing free →
What you'll take away

Good product photos don't need a studio or a €2,000 camera. They need light you can control, a steady camera and two settings most beginners leave to automatic mode: white balance and exposure. This lesson is the first part of the course “DIY product photos”. It shows which gear is worth buying, how to set light and what a complete setup under €150 looks like. What Amazon requires from the finished main image is covered in the main image lesson, which images your gallery needs in the image stack lesson. This one is about the tools you use to produce both yourself.

1

Phone or camera: what you really need

A current smartphone is almost always enough for Amazon product photos. Most phones save photos at roughly 12 megapixels or more, about 4,000 × 3,000 pixels. For a finished 2,000 × 2,000 pixel image, that leaves enough headroom for cropping. With products, the difference between an amateur and a professional photo is rarely the sensor. It's the light and the care that goes into the setup.

A camera wins with a larger sensor (less noise in low light), interchangeable lenses and full manual control. That pays off with many products, very shiny surfaces or tiny details. It isn't required to get started.

The five phone settings that make the difference

  • Pick the right lens: on most smartphones the main lens is a wide angle (around 24 to 26 mm full-frame equivalent). Very close to the product it distorts: the front looks too big, vertical edges tilt. Use the 2x or 3x lens if your phone has one, and step back. Avoid digital zoom between lenses, it only enlarges pixels.
  • Lock focus and exposure: on many phones you hold your finger on the subject until a lock indicator appears. Otherwise the phone meters every shot again and your series ends up brighter one moment, darker the next.
  • Portrait mode off: the artificial blur cuts edges incorrectly, especially around handles, openings and fine parts.
  • Show the grid: it helps you align the product straight and hit the same framing across a series.
  • RAW, if available: a RAW format (often DNG) stores more image information than a JPEG. White balance and brightness can be corrected later without quality loss.
In plain terms

The camera is the brush, the light is the paint. An expensive brush doesn't turn bad paint into a good picture. A simple phone with good, steady light beats an expensive camera under a ceiling lamp.

2

Light tent, sweep or open setup

Before you buy lights, decide where your product will stand. There are three basic setups, and each suits different products and images.

SetupWhat it isStrong forWeak for
Light tent (light cube)A folding cube of white fabric, usually 40 to 80 cm, sometimes with built-in LED stripsSmall products, quick shots for cut-outs, even light without prior knowledgeLarge products, shiny surfaces (the tent reflects all around), images with depth and character
SweepA sheet of photo card or paper running from the table up the wall without a foldMid-sized products, deliberately placed light, main image and gallery shots from one setupTight spaces with no wall or stand to fix it to
Open setupTable, window light, real surfaces such as wood, stone or linenDetail, in-use and lifestyle shotsMain images, because the background has to be replaced completely later

Rule of thumb for the light tent: the product should be at most half as wide as the tent opening, otherwise there's no room for a crease-free background and soft light from the side. For two 19.5 cm spice mills, a 60 cm tent is enough. For a laundry basket it isn't.

The sweep is the most versatile setup. The curve hides the visible edge between table and wall, which shows up in photos as a gray line. Place the product at least 40 to 50 cm in front of the curve. Its shadow then doesn't fall on the background, and you can brighten the background separately.

3

Daylight, continuous light, flash

Light has two properties that decide your photo: how soft it is and what color it has. Soft light comes from a large surface (a window with a curtain, a softbox, a light tent) and creates gentle shadows with smooth transitions. Hard light comes from a small source (direct sun, a bare bulb) and creates sharp, dark shadows.

  • Window daylight: free and nicely soft as long as no direct sun comes in (north-facing window, overcast day or a thin white curtain). The catch: brightness and color change with the time of day and the weather.
  • Continuous light (LED): always the same, repeatable as often as you like, and you see what you get before you shoot. Watch two specs: a color temperature around 5,600 kelvin (daylight white) and a color rendering index (CRI) of at least 95. CRI describes on a scale up to 100 how naturally a light source renders colors. Cheap lights with a low value make wood look greenish or skin look sallow. Dimmable panels are ideal.
  • Flash: a lot of light in a very short time, freezes motion. You need a camera with a flash connection and practice, because you only see the result after the shot. For beginners, continuous light is easier.
Important

Don't mix light sources of different colors. Window light (rather bluish) plus a warm ceiling lamp gives two color casts in one image that no single white balance can fix at the same time: one side of the product turns neutral, the other stays orange. So before you shoot: ceiling lamp off and curtains closed if you work with LEDs, or LEDs off if you work with the window.

The base lighting for almost any product

  1. Key light at an angle from the front or side, about 45 degrees to the product and slightly raised. It shapes the product with light and shadow.
  2. Fill on the opposite side: a white foam board that bounces light back and opens up the shadows without erasing them.
  3. Background light (optional, but worth its weight in gold for the main image): a second light that only brightens the background so it ends up brighter than the product.
Example

For the AURELO spice mill set (two mills in matte white ceramic with an oak head, €24.99), the key light stands front left at 45 degrees, 50 cm away and 20 cm above the heads of the mills. A white foam board on the right acts as fill. Result: the round ceramic bodies get a soft gradient from bright to slightly darker, and exactly that gradient shows that the mills are round. Lit straight from the front they would be two flat white shapes, and the grain of the oak would be lost.

4

Tripod and trigger: the underrated half

A tripod looks like an extra for advanced users. In fact, after light it's the most important purchase, for three reasons:

  • Same framing for the whole series: variants, colors and accessories are shot from exactly the same angle, and later reshoots match the rest.
  • Low light without shake: on a tripod the exposure time can be longer. The camera can therefore work at a low sensitivity (ISO), and low ISO means less image noise. Noise shows immediately when shoppers zoom on the product page.
  • Hands free: you can move lights, fill and product without losing your framing.

Shoot with the self-timer (2 to 3 seconds) or a radio trigger so your finger doesn't shake the shot. For a phone, a tripod with a clamp that extends to eye level and has a tilting head is enough.

The workflow on set

  1. Switch off stray light: ceiling lamp off, curtains closed (or LEDs off if you work with the window).
  2. Build the background and place the product in front of it.
  3. Camera on the tripod, choose the lens, set the framing.
  4. Set the light: key light, fill, background light if needed. Only now, because you set light for the camera's point of view.
  5. Set white balance and shoot the gray card. Only after the light, because it measures the light's color.
  6. Lock focus and exposure, take a test shot and check the histogram. Last, because any change to the light shifts the exposure.
  7. Shoot the series with the self-timer.
5

White balance: colors that match what arrives

Every light source has a color, measured in kelvin. Your eye compensates automatically, the camera has to be told. If white balance is off, the whole photo gets a color cast, and your product has a different color in the listing than in the box. That's not a cosmetic issue: “color differs” is a typical return reason (more in the reducing returns lesson).

Light sourceColor temperature (approx.)Effect without correction
Candle, warm incandescent bulb1,900 to 2,700 Kclearly orange
Halogen, warm white LED3,000 to 3,200 Kyellowish
Midday sun, photo LED5,000 to 5,600 Kneutral
Overcast sky6,000 to 7,000 Kslightly bluish
Shade under blue sky7,000 to 10,000 Kclearly blue

How to set white balance correctly:

  • Don't leave it on auto: auto white balance recalculates every image. If you shoot a white and then a green variant, it shifts the colors differently. Set a fixed kelvin value that matches your lights, for example 5,600 K.
  • Work with a gray card: a gray card is a neutral gray, matte card. Shoot it once at the start of every series in the product's light. In your editor, click the card with the white balance eyedropper and the colors are right. You then apply that correction to every image in the series.
  • Compare with the real product: at the end, hold the product next to the screen. If the impression doesn't match, the screen itself is often the cause, for example a night mode with a yellow filter.
6

Exposure: why white turns gray

Every camera's light meter assumes that a subject is mid gray on average. If you shoot a bright product against a white background, the camera thinks the scene is too bright and darkens it. Result: gray background, dirty-looking white. With a dark product on a dark base the opposite happens.

  • Exposure compensation upward: for bright scenes on white, compensate by about +1 to +2 stops (on cameras often shown as “+1.0 EV”, on phones usually a brightness slider next to the focus point).
  • Read the histogram: the histogram shows how many pixels have which brightness. In a photo on white, a big peak sits far right (the background) and the product spreads across the middle. The background touching the right edge is intended. If parts of the product touch it too, they're blown out: texture and detail are gone and can't be recovered.
  • The three controls: shutter speed, aperture and ISO. On a phone the aperture is usually fixed. On a camera, f/8 to f/11 (enough sharpness front to back) and ISO 100 to 200 are a good start for products, and thanks to the tripod even 1/15 second is no problem.
Most common mistake

“I'll brighten it later in editing.” An underexposed photo brightened afterwards gets noisy in the dark areas and loses color accuracy. An overexposed product is even worse: blown-out areas stay white no matter how much you darken them. Exposure is fixed on set, not at the computer.

7

The setup under €150

With this kit you shoot main images, detail and gallery shots for products up to roughly shoebox size. The prices are guide values from online retail in autumn 2026 and vary considerably by seller.

ItemWhat to look forGuide price
2 LED panels with light standsCRI 95 or higher, 5,600 K or adjustable, dimmable, mains adapter rather than battery only€60 to €80
Tripod with phone clamp and radio triggerextends to eye level, tilting head€20 to €30
Background60 cm light tent without built-in LEDs, or a roll of white photo card for the sweep€15 to €25
2 white foam boards, 1 black cardas fill and to block light€8 to €12
Gray cardneutral gray, matte, not glossy€5 to €10
Small itemstape, putty, cotton gloves, microfiber cloth, air blower€8 to €12
Example

The shopping list for the AURELO set: two LED panels with stands for €68, a phone tripod with radio trigger for €24, a roll of white photo card for €18 (a sweep instead of a light tent, because the oak heads would look flat in the tent's all-around light), foam boards and black card for €10, a gray card for €7 and small items for €10. Total: €137. The kit is then ready for every further product, and reshoots for a new variant cost nothing but time.

Tip

Light tents with built-in LED strips are convenient, but often not dimmable. Separate lights cost hardly more and also work for detail and lifestyle shots later.

Before you shoot
  • Ceiling light off, no mix of window light and lamp light.
  • Product clean and at least 40 cm in front of the background.
  • Phone on the tripod, 2x or 3x lens, portrait mode off.
  • Key light at an angle (about 45 degrees), fill opposite.
  • White balance fixed, gray card shot once.
  • Focus and exposure locked, compensation for bright scenes set.
  • Histogram checked: product not blown out.
  • Shutter released by self-timer or radio trigger.
8

Expert insight: controlling light with distance and size

Professionals don't move their lights by guesswork. Two physical rules predict brightness, softness and the gap between product and background before you take the first photo.

Rule 1, the inverse square law: brightness falls with the square of the distance. Double the distance means a quarter of the light, which is two stops. Triple the distance means a ninth. For two points lit by the same lamp: brightness at the far point = (distance to the near point ÷ distance to the far point)², as a share of the brightness at the near point.

Rule 2, relative size: how soft light is doesn't depend on the size of the lamp but on its size relative to its distance. A 30 cm panel 40 cm from the product is, from the product's point of view, a large surface: soft shadows. The same panel 2 m away acts like a point: hard shadows. The sun is huge, but so far away that its light is hard.

Example

The AURELO key light stands 50 cm in front of the mills, the sweep starts 50 cm behind them, so 100 cm from the light. Calculation: (50 ÷ 100)² = 0.25. The background gets only a quarter of the light, two stops less than the mills, and turns gray in the photo although the card is white. If you move the light back to 150 cm, the card is 250 cm away: (150 ÷ 250)² = 0.36. The gap shrinks, but the light gets harder and weaker. The clean solution is the second panel: key light close for soft light, background light separate, set so the card is about one stop brighter than the mills.

Three moves follow from this that you can apply without calculating:

  • Softer light: move the light closer or put a diffuser in front. Both enlarge the light surface from the product's point of view.
  • Darker background (for mood): light close to the product, product far from the wall. The light falls off strongly on its way to the background.
  • Brighter background (for the main image): a dedicated light for the background instead of one strong lamp for everything.

Once you've understood these two rules, a new setup takes two or three test shots instead of twenty.

✎ Practice

Your turn: 2 exercises

Solve them to unlock the quiz. Up to 30 points each when you get it right first time without a hint.

1
Put in order

Build the photo set in the right order

You're shooting the AURELO spice mill set with two LED panels on a sweep. Put the steps on set in the right order.

  1. Fix the white balance and shoot the gray card
  2. Set the key light at 45 degrees, fill on the opposite side
  3. Lock focus and exposure, check a test shot in the histogram
  4. Switch off the ceiling lamp and close the curtains
  5. Build the sweep and place the mills 50 cm in front of it
  6. Phone on the tripod, choose the 2x lens, set the framing
  7. Shoot the series with the self-timer
2
Calculation

How much light reaches the background?

Your key light stands 40 cm in front of the AURELO mills. The white wall behind them is 120 cm from the same light. There's no background light.

What percentage of the brightness falling on the mills reaches the wall? One decimal place.

Check yourself

6 quick questions, one at a time, with instant feedback. With a free account your progress is saved.

You shoot a small tin from 15 cm away with your phone's main lens. What's the problem?
On most phones the main lens is a wide angle. Up close the front looks too big and edges tilt. With the 2x or 3x lens from further away, proportions stay true.
What does a CRI of 95 on an LED light's packaging tell you?
The color rendering index (CRI) describes on a scale up to 100 how naturally a light source renders colors. For product photos, 95 or higher is a good practical value.
In the morning light comes through the window, and the warm ceiling lamp is on as well. What happens in the photo?
Window light is rather bluish, the ceiling lamp orange. White balance can only neutralize one light color, so always use one type of light only.
Your bright product in front of a white background looks gray in the photo. What's the most likely cause?
Light meters assume a mid-gray subject. For bright scenes you compensate by about +1 to +2 stops and check the histogram.
Why do you shoot a gray card at the start of every series?
With the white balance eyedropper on the gray card, colors are right across the whole image. You then apply the correction to every photo in the series.
Why is a tripod worth it even when there's plenty of light?
A fixed camera means variants and reshoots from the same angle, and longer exposures without shake. That keeps ISO low and the image clean.

Frequently asked

Is a cheap smartphone good enough for Amazon product photos?

Usually yes, if it delivers photos at around 12 megapixels and you have light, tripod and settings under control. Limits show in low light (noise), with very small details and with highly reflective products. Then a camera with a larger sensor pays off, even a used one.

Do I need a light tent for product photos?

For small products and quick shots for cut-outs it's convenient. For mid-sized products, wood, metal or images with depth, a sweep of photo card with two separate lights is more versatile. You can get a compliant main image with either setup.

What color temperature should my lights have?

Around 5,600 kelvin (daylight white), and all lights in the setup the same. More important than the exact value is that no second light color creeps in. Set the camera's white balance to the same fixed value and check with a gray card.

← Previous lessonMeasuring profit per ASIN properly: contribution margin instead of gut feeling Next lesson →Shooting your own main image: setup, cut-out, export
Enes Kurt
Founder of Listimo

Everything in this academy comes from more than ten years of hands-on work with Amazon listings, the same playbook behind Listimo: the tool that finds what holds an Amazon listing back and fixes it.